Home Smith Energy Equipment Manufacturers After Sales Quotation Careers Contact

Equipment

Condensing Boilers

    P-K Sonic

    • 1500 MBTU to 4000 MBTU
    • CSA certified at 96% efficiency
    • Unique stainless alloys resist corrosive condensation
    • Patented DUET™ Technology
    • Compact design, up to 60% smaller than the leading competition
    • Easy to use ENVI® Control maximizes boiler plant efficiency
    • Certified low NOx performance
    • Full modulation burner with 5:1 turndown
    • Variable speed combustion air blower

    P-K MACH

    • 750 MBTU to 4000 MBTU
    • CSA certified at 92%-96% efficiency
    • Fit through a standard 36 inch doorway or a standard elevator
    • Fully independent cast aluminum heat exchangers
    • Works well at low or high temperatures
    • Powerful new tool for building LEED® points
    • Barely audible, even at high fire
    • Full modulation burner with 5:1 turndown
    • Actual net thermal efficiencies may be achieved up to 99%

    P-K MACH CM Series

    • 300 MBTU to 500 MBTU
    • Runs on natural gas or liquid propane
    • Versatile piping arrangements
    • >90% CSA certified efficiency
    • Wall mounting bracket (optional)
    • ENVI control
    • Removable front panel and top service access panel
    • Protocol converter (optional) for LONWORKS, BACNET or METASYS N2
    • Zero clearance

    Fulton Endura

    • 750 MBTU to 2000 MBTU
    • Ultra-high efficiencies up to 99%
    • Fully modulating burner
    • Fully duplex Stainless Steel heat exchanger
    • Primary/Variable flow hydronic system applications
    • Low NOX emissions
    • AHRI Certified

    Fulton Vantage

    • 2000 MBTU to 6000 MBTU
    • Ultra High Efficiencies
    • Linkageless Modulation
    • Dual Fuel Capabilities
    • Lifetime Thermal Shock Warranty

    Fulton Endura +

    • 2500 MBTU to 3000 MBTU
    • Designed for variable primary flow
    • Up to 15:1 turndown; O2 compensation
    • Natural gas pressures down to 4” WC
    • Fits through a standard doorway

Non-Condensing Boilers

    P-K Modu-Fire FD

    • 750 MBTU to 3000 MBTU
    • Efficiency up to 88%
    • Small, modular configuration
    • Changes both fuel and air at a constant ratio to match boiler output to actual heat demand
    • Smooth 5:1 turndown can track varying loads down to 20% of rated capacity
    • Eliminates short cycling in high ΔT variable speed pumping systems
    • Accurate firing rate feedback – analog output signal proportional to firing rate
    • Small diameter Category IV venting
    • Zero clearance

     

    P-K Thermific

    • 700 MBTU to 2000 MBTU
    • Efficiency up to 85%
    • Completely packaged design
    • Compact/modular design allows multiple units to be installed in tandem
    • Vertical burner/heat exchanger design
    • Unique integral finned copper water tubes
    • High heat transfer ratio
    • Lo-Hi-Lo operating controls on some models
    • Operates quietly, below OSHA standards
    • CSA (AGA/CGA) certified and ASME approved

     

Water Heaters

    Sofame Technologies Percomax

    • Direct-contact water heater
    • Very high efficiencies; up to 100% (based on HHV)
    • Maximum flue gas temperatures no more than 10°F (5.5°C) greater than cold water temperature at inlet
    • Minimum maintenance required
    • Reduced emission of atmospheric pollutants
    • No supervision required (unit is not classed as a pressure vessel)
    • Rapid unit start-up (instantaneous hot water production)
    • Can be installed outside

    P-K MACH’n Roll

    • 300 MBTU to 1050 MBTU
    • Domestic water loop is isolated from the boiler loop
    • Precise temperature regulation with no mixing valve required
    • Return to Storage Tank
    • Onboard P-K ENVI® control system
    • Certified low NOx performance
    • Aluminum alloy heat exchanger
    • Full modulation burner with 5:1 turndown
    • Produce domestic water up to 140°F and still operate the boiler in the condensing mode

    Rex

    • Indirect water heater tank
    • 50 000 BTU/HR to 900 000 BTU/HR
    • Stainless Steel distributor
    • High efficiency
    • Long life and an economical way of heating domestic water
    • No stagant water in the coils

Heat Recovery Economizers

    Enervex VHX

    • Heat recovery center from 1000 MBTU to 33 000 MBTU
    • Stack economizers and heat exchangers
    • Integrated modulating bypass damper
    • Modular heat exchanger concept
    • Stainless steel housing and heat exchanger (316L)
    • Condensing or non-condensing applications
    • Single or multiple boilers
    • Vertical or horizontal installation
    • Forced draft or atmospheric boilers

    Super Radiator Coils Economizers

    • Standard and non-standard sizes between 200 – 1,000 BHP
    • Compact design with removable access panels
    • Stainless steel interior with stainless steel heat exchanger
    • Carbon steel or stainless steel tube and fin combinations provide maximum performance and value
    • ASME Section VIII certified

    Sofame Technologies Percotherm

    • Direct-contact stack condensing economizer
    • Very high efficiency; up to 100% (based on HHV)
    • Boiler seasonal efficiency improved by up to 20%
    • Maximum flue gas temperatures no more than 10°F (5.5°C) greater than cold water temperature at inlet
    • Minimum maintenance required
    • Reduced emission of atmospheric pollutants
    • No supervision required (unit is not classed as a pressure vessel)
    • Reduction of installed boiler capacity
    • Can be installed outside

Commercial boiler and water heater exhaust fans

    Enervex CASV

    • Demand controlled exhaust system designed for commercial boilers and water heaters in buildings where the exhaust is powered by a chimney fan on the exterior of the building
    • Extremely low noise level
    • Priority Operation Function and Bearing Cycle Activation
    • Interlocks 6 appliances (standard) or as many as necessary with add-on relay boards
    • Cast aluminum chimney fan and impeller for use with Category I, II, III and IV appliances (condensing and non-condensing)
    • Spark-resistant construction with high-temperature TEFC-motor with a Class H temperature rating, direct drive and true variable speed (inverter-duty)
    • Maintenance free and service-friendly design

    Enervex CASI

    • Demand controlled exhaust system designed for commercial boilers and water heaters in buildings where the exhaust is powered by an inline power venter installed insdie a building
    • Extremely low noise level
    • Priority Operation Function and Bearing Cycle Activation
    • Interlocks 6 appliances (standard) or as many as necessary with add-on boards
    • SS316L and aluminum impeller for use with Category I, II, III and IV appliances (condensing and noncondensing)
    • Spark-resistant construction with TEFC-motor with direct drive and true variable speed (inverter duty)
    • Maintenance free and service-friendly design

    Enervex MODS

    • Demand controlled exhaust system that’s designed for buildings that experience excessive chimney draft
    • Full modulation and 100% over-draft control
    • Integrated safety system with Proven Draft function, over-pressure cut-out switch and operation verification
    • Priority Operation Function and Bearing Cycle Activation
    • Interlocks 6 appliances (standard) or as many as necessary with add-on boards
    • Multi-blade damper for fast and accurate draft control
    • Fast-acting, direct drive actuator with brushless motor
    • Maintenance free and service-friendly design, the MODS System can be combined with a CASV or CASI and an MCAS system

    Enervex MCAS

    • Demand controlled combustion or make-up air supply system
    • Extremely low noise level
    • Priority Operation Function and Bearing Cycle Activation
    • Interlocks 6 appliances (standard) or as many as necessary with add-on boards
    • Easy programming of essential functions (80 parameters are programmable for customized solutions)
    • Spark-resistant construction with TEFC-motor with direct drive and true variable speed (inverter duty)
    • Maintenance free and service-friendly design

Multi level demand control Exhaust Systems

    Enervex MBESV

    • Demand controlled ventilation system designed specifically for multi-story buildings that have kitchen hoods, bathrooms or clothes dryers on multiple floors
    • Easy programming of essential functions
    • Spark-resistant construction with TEFC-motor with direct drive and true variable speed
    • Extremely suitable for retrofitting
    • Listed to UL705, Standard for Power Ventilators

     

Heat Exchangers

    Mueller Temp-Plate

    • Available in most materials
    • High operating pressures and temperatures
    • Corrosion resistant
    • Easily formed to fit the shape you need
    • Easily cleanable, attractive finishes available
    • Low pressure drop design
    • Food-grade designs available

    Mueller Plate and frame Heat Exchangers

    • High Efficiency Heat Transfer Performance
    • Easy to Clean and Inspect
    • True Counterflow
    • Close Approach Temperatures
    • Expandable
    • High Viscosity Applications
    • Cross Contamination Eliminated
    • “Free-Flow” Plate Heat Exchangers

    Mueller Brazed Plate Heat Exchangers

    • Compact engineered systems
    • Cost effective, superior solution to your heat transfer applications
    • Reduce cooling media volume, further energy consumption
    • Simplify maintenance and repair

Fancoils

Heat transfer products

    Coilmaster Corporation Remote Air Cooled Condenser

    • 4 to 245 tons for air-conditioning duty
    • Standard Heavy gauge galvanized steel
    • Coil coatings avalaible

    Coilmaster Corporation Fluid Coils

    • Custom coils and booster coils
    • Turbulators are available
    • Custom connection orientations to match installation requirements

    Coilmaster Corporation Fluid Coolers

    •  Units ranging from 1 to 14 fans
    • Choice of single and double-fan width units
    • Factory-installed controls